Back to Videos
Is this page helpful?
2097x
001526
Dipl.-Ing. (FH) Andreas Hörold
2020-07-08

How to Be More Productive Using RFEM

This webinar demonstrates useful features in RFEM to increase productivity and efficiency with your daily projects.

Time Schedule:
00:00 Introduction
06:00 Model generation
34:10 Parameteric models
44:00 Load input and generation
51:15 Results and documentation

Links
Downloads
Slides to Webinar "How to Be More Productive Using RFEM" (PDF)
7.36 MB
RF-COM Example of Stair from Webinar "How to Be More Productive Using RFEM" (XLS)
788 KB
  • Mia: AI Assistant
  • Latest Videos
Videos
Models to Download
Knowledge Base Articles
Excel Data Imported into RFEM for Variable Member Load
The ASCE 7-22 standard requires both balanced and unbalanced snow load case scenarios for a structure's design consideration. While this may be more intuitive for flat or even gable/hip type roofs, the determination of snow loads is increasingly difficult for arch roofs due to complex geometry. However, with guidance from ASCE 7-22 on snow load calculations for curved roofs and RFEM's efficient load application tools, it is possible to consider both balanced and unbalanced snow loads for a reliable and safe structure design.
Experimental Wind Tunnel Test – Aachen University
Validating CFD simulations with experimental data enhances accuracy by comparing simulation outcomes with real-world conditions. This process identifies discrepancies, allowing adjustments to enhance model reliability. Ultimately, it builds confidence in the simulation's ability to predict wind load scenarios.
KB 001884 | AISC Chapter F Lateral Torsional Buckling Versus Eigenvalue Calculation Methods Compared in RFEM 6
Utilizing the Steel Design Add-on, steel design is possible according to the AISC 360-22 standard. The following article will compare the result output when calculating lateral torsional buckling according to Chapter F vs. an Eigenvalue Analysis.
Basic Shapes of Membrane Structures [1]
This paper is focused on the specific aspects of designing membrane structures that have specific requirements, such as form-finding and cutting pattern generation. An integral part of the design of these structures is the process of finding suitable prestressed shapes and generating cutting patterns. The text briefly describes two basic processes in the design of membrane structures. The physical principles are explained and the individual theses illustrated by examples.
Screenshots
Product Features
Feature 002423 | Displaying Results in Solids

The results of solid stresses can be displayed as colored 3D points in the finite elements.

Feature 002012 | Generation of Snow Loads

Do you want your structures to remain upright even in wind and snow? Then rely on the load wizards for plate and frame structures. You can now generate wind loads according to EN 1991‑1‑4 and snow loads according to EN 1991‑1‑3 (as well as other international standards). The load cases are generated depending on the roof shape.

Feature 002013 | Generation of Wind Loads

Wind loads are also not a problem in your design. You can automatically generate wind loads as member loads or area loads (RFEM) on the following structural components:

  • Vertical walls
  • Flat roofs
  • Monopitch roofs
  • Duopitch/troughed roofs
  • Vertical walls with duopitch roof
  • Vertical walls with flat/monopitch roof

The following standards are available to you:

  • European Union | Flag EN 1991-1-3 (incl. National Annexes)
  • EN-US | Flag ASCE 7
  • Canada | Flag NBC
  • Spain Flag CTE DB-SE-AE
  • South Africa Flag SANS 10160
  • People's Republic of China | Flag GB 50009
  • Italy Flag NTC
Feature 002012 | Generation of Snow Loads

Do your structures also have to withstand snowfall? Use the Snow Load Wizard to generate snow loads as member loads or surface loads.

The following standards are available:

  • European Union | Flag EN 1991-1-3 (incl. National Annexes)
  • EN-US | Flag ASCE 7
  • Canada | Flag NBC
  • Switzerland | Flag SIA 261
  • Spain Flag CTE DB-SE-AE
  • People's Republic of China | Flag GB 50009
  • India | Flag IS 875
Frequently Asked Questions (FAQ)

Where can I find the update reports for RFEM 5, RSTAB 8, SHAPE-THIN, SHAPE-MASSIVE, RX-TIMBER, CRANEWAY, PLATE-BUCKLING, COMPOSITE-BEAM?

For my NVIDIA graphics card, I need to select between a driver from the "Production Branch" and a "New Feature Branch." Which driver is best suited for RFEM/RSTAB?
Is it possible to quickly evaluate whether the mesh used is fine enough?
Why do the min/max values of the total displacement not match the deformations when working with result combinations?
Computational Fluid Dynamics (CFD) is a powerful tool in modern engineering practice. However, as with all simulation methods, the question arises: how reliable are the results?

Why do I get an error message about invalid material when defining timber surfaces?
Customer Projects
Recommended Products for You