Back

003256

2024-06-26

Selected Concrete Features in RFEM 6

In this webinar, we will show you the selected concrete features in RFEM 6.

$Selected Concrete Features \n in RFEM 6$

Upcoming

2024-09-12

2:00 PM – 3:00 PM CEST

English

Add to Calendar Register

Free

Product Feature

RFEM 6 | FEA Software

Free Webinar | Selected Concrete Features in RFEM 6

In this webinar, we will show you the selected concrete features in RFEM 6.

Do you have any questions about the topic? You can send them to us up to two days before the webinar. If possible, we will answer them during the webinar.

After the event, you can find the models presented in the webinar below, under Models to Download. This allows you to independently follow the webinar step by step.

Furthermore, each participant will receive a certificate with the name specified during the registration.

Time Schedule
- Introduction
- Reinforcement layout
- Fire resistance design using the table method
- Punching shear design
- Fatigue design
- SLS design

Notes

During the presentation, you can ask individual questions.

A computer with Internet access is required as well as a speaker, headphones, headset, or any other listening device. Alternatively, you can dial in using a phone line for audio connection.

Take advantage of this free webinar and sign up today! The number of participants is limited. After your registration is complete, you will receive a confirmation email, including the information on how to join the webinar.

Dipl.-Ing. (FH) Andreas Hörold

Marketing & Public Relations

Mr. Hörold takes care of the Dlubal Software website, moderates the German and English webinars, and creates newsletters and marketing materials.

Dipl.-Ing. (FH) Richard Haase

Product Engineering & Customer Support

Mr. Haase is responsible for development in the area of reinforced concrete structures, and provides technical support to our customers.

Location

Online

Links

Do you have any questions?

Events

2024-07-04

Geotechnical Analysis with Construction Stages in RFEM 6

Webinar

Geotechnical Analysis with Construction Stages in RFEM 6

2024-07-11

Wind Load Transfer from RWIND 2 to RFEM 6

Webinar

Wind Load Transfer from RWIND 2 to RFEM 6

2024-07-18

Fire Resistance Design of Timber Structures in RFEM 6

Webinar

Fire Resistance Design of Timber Structures in RFEM 6

2024-07-24

Webinar

Linear Stability Analysis in RFEM 6 and RSTAB 9

2024-07-25

Modeling and Stress Analysis of Solid Models in RFEM 6

Webinar

Modeling and Stress Analysis of Solid Models in RFEM 6

2024-08-01

Most Frequently Asked Questions Answered by Dlubal Support Team

Webinar

Most Frequently Asked Questions Answered by Dlubal Support Team | July 2024

2024-08-08

Structures with Reinforced Aluminum Sections

Webinar

Structures with Reinforced Aluminum Sections in RSECTION 1 and RFEM 6

2024-08-15

$Design of Timber Panel Walls in \n RFEM 6$

Webinar

Design of Timber Panel Walls in RFEM 6

2024-08-22

Steel Joint Design in RFEM 6 Using Practical Example

Webinar

Steel Joint Design in RFEM 6 Using Practical Example

2024-09-12

$Selected Concrete Features \n in RFEM 6$

Webinar

Selected Concrete Features in RFEM 6

2024-09-30 - 2024-10-03

Trade Fair

BATIMAT 2024

2024-10-16

Online Training

RFEM 6 | Students | Introduction to Member Design

Videos

Product Feature

RFEM 6 | FEA Software

Length: 00:00:00 min

Event

Calculation of Reinforced Concrete Slabs in RFEM 6

Length: 01:09:36 min

Knowledge Base

KB 001821 | Defining Rib Widths of Downstand Beams Using Example of Two-Span Beam

Length: 00:00:50 min

Event

Webinar | Design of Massive RSECTION Sections in RFEM 6

Length: 00:47:34 min

FAQ

FAQ 005388 | How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on...

Length: 00:01:00 min

Knowledge Base

KB 001838 | Design of Ribs, Folded Plate Structures, and Surfaces Using Result Members in RFEM 6

Length: 00:00:47 min

General

Structural Analysis and Design Software for Concrete Structures | RFEM 6 & RSTAB 9 by Dlubal Software

Length: 00:03:40 min

FAQ

FAQ 005279 | Although all the member design checks have been fulfilled, I get the "Not Covered...

Length: 00:00:50 min

FAQ

FAQ 005223 | Where can I find the graphical results of punching shear in the concrete design? Especially...

Length: 00:00:43 min

Playlist

Models to Download

Model 004552 | Design Level 1 - Fatigue Design

44x

Dome Structure

Model 004505 | Building with Inclined Reinforced Concrete Columns

625x

30x

Building with Inclined Reinforced Concrete Columns

Single-Span Beam for Fiber-Reinforced Concrete Design

510x

30x

Single-Span Beam with Fiber-Reinforced Concrete as Surface Component or Frame Structure

KB 001838 | Design of Ribs, Folded Plate Structures, and Surfaces Using Result Members in RFEM 6

648x

12x

Folded Plate Structures and Surfaces

660x

16x

Verification Example 1000 | Concrete Column with Nominal Curvature Method

603x

17x

Reinforcement Description

983x

48x

Plate with Rib Member

378x

Model of Elevator Shaft

KB 001842 | Slab with Automatic Surface Reinforcement as Supplement

246x

KB 001842 | Automatic Design Process of Provided Surface Reinforcement

Knowledge Base Articles

In order to correctly design a downstand beam or a T-beam in RFEM 6 using the Concrete Design add-on, it is essential to determine the flange widths for the rib members. This article describes the input options for a two-span beam and the calculation of the flange dimensions according to EN 1992-1-1.

KB 001838 | Design of Ribs, Folded Plate Structures, and Surfaces Using Result Members

If you want to use a pure surface model, for example, when determining the internal forces and moments, but the structural component is still designed on the member model, you can take advantage of a result beam.

According to EN 1992-1-1 [1], a beam is a member of which the span is no less than 3 times the overall section depth. Otherwise, the structural element should be considered as a deep beam. The behavior of deep beams (that is, beams with a span less than 3 times the section depth) is different from the behavior of normal beams (that is, beams with a span that is 3 times greater than the section depth). However, designing deep beams is often necessary when analyzing the structural components of reinforced concrete structures, since they are used for window and door lintels, upstand and downstand beams, the connection between split-level slabs, and frame systems.

Critical Perimeter Around Column Considering One Opening

The punching shear design, in line with EN 1992-1-1, should be performed for slabs with a concentrated load or reaction. The node where the design of punching shear resistance is performed (that is, where there is a punching problem) is called a node of punching shear. The concentrated load at these nodes can be introduced by columns, concentrated force, or nodal supports. The end of the linear load introduction on slabs is also regarded as a concentrated load and therefore, the shear resistance at wall ends, wall corners, and ends or corners of line loads and line supports should be controlled as well.

Screenshots

Product Features

Feature 002670 | Fatigue Design According to EN 1992-1-1, Chapter 6.8

With the Concrete Design add-on, you can perform the fatigue design of members and surfaces according to EN 1992‑1‑1, Chapter 6.8.

For the fatigue design, you can optionally select two methods or design levels in the design configurations:

Design Level 1: Simplified design according to 6.8.6 and 6.8.7(2): The simplified design is performed for frequent action combinations according to EN 1992‑1‑1, Chapter 6.8.6 (2), and EN 1990, Eq. (6.15b) with the traffic loads relevant in the serviceability state. A maximum stress range according to 6.8.6 is designed for the reinforcing steel. The concrete compressive stress is determined by means of the upper and lower allowable stress according to 6.8.7(2).
Design Level 2: Design of damage equivalent stress acc. to 6.8.5 and 6.8.7(1) (simplified fatigue design): The design using damage equivalent stress ranges is performed for the fatigue combination according to EN 1992‑1‑1, Chapter 6.8.3, Eq. (6.69) with the specifically defined cyclic action Q_fat.

Feature 002671 | Seismic Design of Reinforced Concrete Members According to EC 8

The Concrete Design add-on allows you to perform the seismic design of reinforced concrete members according to EC 8. This includes, among other things, the following functionalities:

Seismic design configurations
Differentiation of the ductility classes DCL, DCM, DCH
Option to transfer the behavior factor from a dynamic analysis
Check of the limit value for the behavior factor
Capacity design checks of "Strong column - weak beam"
Detailing and particular rules for curvature ductility factor
Detailing and particular rules for local ductility

Feature 002654 | Design of Fiber-Reinforced Concrete

In the Concrete Design add-on, you can design structural components made of fiber-reinforced concrete according to the guideline DAfStb Steel Fiber-Reinforced Concrete.

You can use this option for the design according to EN 1992‑1‑1. The design according to the DAfStb guideline is carried out once the concrete of the "Fiber Concrete" type has been assigned to the reinforced structural component.

Go to Explanatory Video

Feature 002652 | "Crosstie" Reinforcement Option for Design According to EN 1992-1-1

In the "Shear Reinforcement" tab, you can select the option "Cross-ties over free rebars with active selection in graphic". It allows you to arrange additional cross-ties on free rebars of the longitudinal reinforcement.

You can activate or deactivate the position of the cross-ties in the Info Graphic. The cross-ties are applied for the ultimate limit state design and the structural design checks. They are available for the design according to EN 1992‑1‑1.

Go to Explanatory Video

Frequently Asked Questions (FAQ)

How can I use graphic templates for multi printing of a reinforcement?

How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?

Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?

Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.

Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?

Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?

Customer Projects

Recommended Products for You

RFEM 6 | Main Program RFEM 6

RFEM 6

Main Program

The new generation of 3D FEA software is used for the structural analysis of members, surfaces, and solids.

Price of First License 4,170.00 USD

RFEM 6 | Design

Concrete Design for RFEM 6

Add-On

The Concrete Design add-on allows for various design checks according to international standards. You can design members, surfaces, and columns, as well as perform punching and deformation analyses.

Price of First License 2,550.00 USD

RFEM 6 | Additional Analysis

Construction Stages Analysis (CSA) for RFEM 6

Add-On

The Construction Stages Analysis (CSA) add-on allows for considering the construction process of structures (member, surface, and solid structures) in RFEM.

Price of First License 1,570.00 USD

RFEM 6 | Additional Analysis

Geotechnical Analysis for RFEM 6

Add-On

In RFEM, the Geotechnical Analysis add-on uses properties from soil samples to determine the soil body to be analyzed. The accurate determination of soil conditions significantly affects the quality of the structural analysis of buildings.

Price of First License 1,120.00 USD

RFEM 6 | Dynamic Analysis

Modal Analysis for RFEM 6

Add-On

The Modal Analysis add-on allows for the calculation of eigenvalues, natural frequencies, and natural periods for member, surface, and solid models.

Price of First License 1,210.00 USD

RFEM 6 | Dynamic Analysis

Response Spectrum Analysis for RFEM 6

Add-On

The Response Spectrum Analysis add-on performs seismic analysis using multi-modal response spectrum analysis. The spectra required for this can be created in compliance with the standards or can be user-defined. The equivalent static forces are generated from them. The add-on includes an extensive library of accelerograms from seismic zones that can be used to generate the response spectra.

Price of First License 1,390.00 USD

RFEM 6 | Dynamic Analysis

Pushover Analysis for RFEM 6

Add-On

Using the Pushover Analysis add-on, you can analyze the seismic actions on a particular building, and thus assess whether the building can withstand an earthquake.

Price of First License 1,300.00 USD

RFEM 6 | Special Solutions

Building Model for RFEM 6

Add-On

The Building Model add-on for RFEM allows you to define and manipulate a building using stories. The stories can be adjusted in many ways afterwards. The information about stories and the entire model (center of gravity) is displayed in tables and graphics.

Price of First License 1,660.00 USD

RFEM 6 | Design

Masonry Design for RFEM 6

Add-On

The Masonry Design add-on for RFEM allows you to design masonry using the finite element method. It was developed as part of the research project titled DDMaS – Digitizing the Design of Masonry Structures. The material model represents the nonlinear behavior of the brick-mortar combination in the form of macro-modeling.

Price of First License 1,660.00 USD